The Arcoro app can be configured to function like a kiosk, allowing you to streamline the clock in/out process where multiple employees need to share the same device. There are many ways a "kiosk" setup can be beneficial, such as:
- A tablet set up in the break room or main entryway of an office so employees can clock in/out when they are coming and leaving.
- A tablet or phone a supervisor can pass during a daily meeting so employees can clock in and pass around the device.
Table of Contents
Please Note
- The app does not have an exclusive "Kiosk Mode" to be enabled. You are configuring the app to help streamline the process.
- It is recommended that the device has a consistent internet connection, either through Wi-Fi or cellular data. If the device does not have a consistent internet connection, someone (such as a supervisor) will need to connect it to the internet periodically and sync the app to send any unsent time punches and data to the Arcoro Time website.
- As employees are not required to use the same device to clock in/out, they can start or end their day with the "kiosk" device, while using an alternate device throughout the day to track their locations/cost codes. All of the employee's time punches will be consolidated and their hours calculated on the Arcoro Time website.
Configuring Your Device for Kiosk Use
Install the Arcoro App
If you have not already installed the Arcoro app, you can refer to the instructions from the following article.
It is recommended to set up and test the app in the office so you can be sure it is functional before using it on-site and know what to expect in case your employees have questions.
Set up Default Locations and Cost Codes
A default location and/or cost code allows you to streamline the location and/or cost codes for an employee when they clock in for themselves by pre-selecting their options. The default location/cost code can be specified by the device or by the employee. Using either or both options will depend on your use case, as explained below with links to the respective steps:
-
Default Location and Cost Codes by Device - This option is best used when employees are clocking in to a specific device, such as a wall-mounted tablet, to simplify the clock-in process.
- For example, all of the employees can clock in on an iPad to start their day. As the employees wait in line and finish clocking in, their manager can perform any equipment checks, go over the daily agenda, and more.
-
Default Location and Cost Codes by Employee - This option is best used when your employees are expected to only use a specific location and/or cost code. It simplifies the clock-in process for any device they use.
- For example, an employee may be expected to deliver materials between locations throughout the day and would only need to use the "Drive" or "Travel" cost code.
Both options can also be used simultaneously, but the default location/cost code to be used can differ depending on the situation.
Situations When Using Default Locations/Cost Codes
Default Location Assigned
- If the Employee has an active default location and the app has an active default location, the app will use the Employee's default location.
- If the Employee has an inactive default location and the app has an active default location, the app will use the app's default location.
- If the Employee has an inactive default location and the app has an inactive default location or no default location assigned, the app will show the location list for the employee to select from.
Default Cost Code Assigned
- If the Employee has an active default cost code and the app has an active default cost code, the app will use the Employee's default cost code.
- If the Employee has an inactive default cost code and the app has an active default cost code, the app will use the app's default cost code.
- If the Employee has an inactive default cost code and the app has an inactive default cost code or no default cost code assigned, the app will show the cost code list for the employee to select from.
Configure App Settings
With Mobile Settings
"Mobile Settings" on the website allows you to manage the settings for all copies of the app connected to your system, establishing a baseline configuration. Any configuration in "Mobile Settings" will be used by the app when the app syncs any data.
- Go to Manage and click on Mobile Settings.
- Click Edit towards the top-right to update your settings.
- Enable Mobile Settings if it has not been enabled.
- Enable the following three options as appropriate:
-
Send time after clocking
- The app will attempt to send any records to the website immediately after they are made. This is typically enabled to help you receive employee punches as soon as possible.
-
Log out after clocking
- After an employee clocks in or out, the app will return to the number pad to allow the next user to enter their PIN and repeat the process. This is typically enabled to remove the "Log Out" step for employees.
-
Override default job
- If an employee's workday has deviated from the expected default location or cost code, they will be able to select a different location/cost code when clocking in. If employees should always use the default location/cost code, this can be skipped.
-
Send time after clocking
- Save your changes. The next time your employees sync their devices, they will receive these settings.
You can learn more about Settings for Arcoro Time here.
With the App
If using "Mobile Settings" to have all copies of the app use the same configuration is not suitable for your organization, you can configure the settings of the app individually. A user with permissions, such as the Administrator Security Role for Mobile, will be able to access the settings of the app.
- Press More at the bottom and press Settings.
- Press General.
- Configure the following settings as appropriate:
-
Send after clock in/out
- The app will attempt to send any time punches to the website immediately after they are made. This is typically enabled to help you receive employee punches as soon as possible. If the time could not be sent for whatever reason, the app will try to send them on the next attempt(s).
-
Log out after clock in or out
- After an employee clocks in or out, the app will return to the number pad to allow the next user to enter their PIN and repeat the process. This is typically enabled to remove the "Log Out" step for employees.
-
Send after clock in/out
- Back out of the menu and use the app as normal.